South Dakota CDL: Double & Triple Trailers Practice Test

Not quite. The answer is drive through quickly.

If you drive through water at higher speeds, your tires may lose their grip of the road and start to skid. When driving through water, slow down and shift into a low gear. Increase engine rpm and apply the brakes gently to keep the brake linings pressed against the brake drums or discs. This will help keep contaminants out of the brakes.

Not quite. The answer is slightly raised.

To test the coupling of the dolly to the second trailer, you'll pull the tractor forward so the dolly will pull against the kingpin of the second trailer. Before doing so, raise the trailer's landing gear slightly. This will prevent damage if the trailer moves, and prevent the trailer from falling onto the ground if the dolly pulls away from the trailer.

Not quite. The answer is directly in front of the converter dolly.

Back the first trailer into position in front of the tongue of the dolly. Hook the dolly to the pintle hook on the first trailer. Then latch the pintle hook securely. Raise the dolly's landing gear.

Not quite. The answer is you couple the third trailer to the second trailer before you couple them to the first trailer.

A triple combination vehicle has four units (not counting the converter dollies): a tractor and three trailers. You couple a triple as follows: 1. Couple the first trailer to the tractor the same way that you couple any combination vehicle. 2. Couple the third trailer to the second trailer using the method for coupling doubles (which will involve the use of a converter dolly). 3. Move another converter dolly into position. 4. Couple the tractor and first trailer to the second and third trailer using the method for coupling doubles (which will involve another converter dolly).

Not quite. The answer is Lower the second semitrailer's landing gear.

When uncoupling a set of standard doubles, the first unit to be uncoupled is the second semitrailer. To do this, lower its landing gear just enough to take some weight off the dolly. Then close the air shut-off valves on the first semitrailer and on the dolly (if so equipped). Disconnect the dolly's air and electrical lines from the second semitrailer. Release the dolly's fifth wheel latch, and pull the tractor forward so it pulls the dolly out from under the second semitrailer. After this is done, start to uncouple the dolly from the first semitrailer. These steps include lowering the dolly's landing gear and unhooking the dolly from the first semitrailer's pintle latch.

Not quite. The answer is air escape from the open valve.

Test the trailer brakes by opening the service line valve at the rear of the rig. You should hear the telltale hiss of air escaping. If you don't, it means that air is not flowing through the entire line, and you will need to investigate.

Not quite. The answer is the vehicle is more likely to roll over or jackknife.

A double or triple combination vehicle is more likely to roll over or jackknife from sudden braking or steering changes. Look far enough ahead that you can slow down or change lanes gradually when necessary.

Not quite. The answer is 10

The formula for following distance is one second per ten feet of vehicle length, plus an extra second if you are traveling over 40 mph. Therefore, for a 100-foot vehicle traveling at 30 mph, you should leave a following distance of 100/10 = 10 seconds. (At or below 40 mph, you do not add an extra second.)

Not quite. The answer is Doubles/triples flip over from quick steering movements more easily than do many other vehicles.

Because of rearward amplification (the "crack-the-whip" effect), steering changes affect the rearmost trailer much more than they affect the front trailer or the tractor. Avoid quick or sharp steering changes that could cause the rearmost trailer to roll over.

Not quite. The answer is supply air to the trailer air brake system with the tractor and then disconnect the emergency line.

If the second trailer lacks spring brakes, set the emergency brakes or chock the wheels.

Not quite. The answer is Both (a) and (b)

Take special care when pulling two or three trailers. In bad weather, under slippery conditions, and in mountain driving, you must be especially careful. There is a greater risk of skids and loss of traction. Also, doubles and triples need more space because they can’t be turned or stopped suddenly. Maintain a greater following distance. Make sure you have large enough gaps before entering or crossing traffic.

Not quite. The answer is closed; latched

When you do a walk-around inspection, you must ensure that the converter dolly is properly connected to the front trailer. Check that the pintle hook of the front trailer is locked onto the eye hook of the converter dolly and properly latched. Otherwise, the dolly could come loose. Even worse, if the dolly comes loose while it's still coupled to the rear trailer, the tow bar could fly up, possibly injuring someone.

Not quite. The answer is make things look smaller and farther away than they really are.

A convex mirror has a wider field of view than a flat mirror. However, objects viewed in a convex mirror look smaller and farther away. Remember this when you're trying to judge the distance of an object that you're viewing in a convex mirror.

Not quite. The answer is 5

In this context, articulation or pivoting means movement between two units separated by a joint, such as between a tractor and a trailer. A triple combination has 3 semitrailers connected with 2 converter dollies. This combination has 5 points of articulation: (1) the fifth wheel of the tractor; (2) the pintle hook of the first trailer; (3) the fifth wheel of the first converter dolly; (4) the pintle hook of the second trailer; and (5) the fifth wheel of the second converter dolly.

Not quite. The answer is enough to take some of the weight off the dolly.

When uncoupling a loaded second or third semitrailer, lower the landing gear until it makes firm contact with the ground. Then crank the landing gear in low gear for a few more turns – just enough to lift some weight off the dolly, but not so much that you lift the trailer off the fifth wheel. This will make it easier to unlatch the fifth wheel now and couple the trailer next time.

Not quite. The answer is A truck has less traction when it's empty than when it's fully loaded.

Trucks that are empty or only lightly loaded take longer to stop because the stiff suspension springs and strong brakes give poor traction and make it easier to lock the wheels.

Not quite. The answer is The heaviest trailer

The rearmost trailer is much more likely to roll over than the front trailer. Position the heaviest trailer directly behind the tractor and position the lightest trailer at the rear.

Not quite. The answer is Allow a greater following distance than for smaller commercial vehicles.

Doubles and triples need more space because they can’t be turned or stopped suddenly. Allow a greater following distance behind the vehicle in front of you.

Not quite. The answer is open; closed

When you are inspecting a double or triple combination, make sure that the service and emergency line shut-off valves are open at the rear of each trailer except the last trailer, where they must be closed.

Not quite. The answer is foot pedal.

You can use the trailer hand valve (also known as a spike or Johnson bar) to test the trailer service brakes. During normal driving, however, all the service brakes on your vehicle are controlled with the foot pedal, which applies air to the service brakes at all the wheels.