Arkansas CDL: Pre-Trip Inspection Practice Test

Not quite. The answer is Leaks

As part of your engine inspection, check the ground below the engine compartment for puddles or dripping liquids.

Not quite. The answer is Clutch and gearshift

To ensure that your vehicle doesn't move once you start the engine, first depress the clutch (unless the vehicle has an automatic transmission) and put the gearshift in neutral (or Park for an automatic transmission). Once the engine has started, slowly release the clutch.

Not quite. The answer is Brake chamber

The brake chamber (one at each wheel) converts air pressure to mechanical force to operate the brake at that wheel. When you press the brake pedal, compressed air from a service tank enters the brake chamber. Air pressure pushes out the brake chamber's pushrod, which moves the slack adjuster. The moving slack adjuster applies the brake.

Not quite. The answer is Check the sight glass.

Your vehicle may provide a way for you to check the coolant level even when the engine is hot. Such devices include reservoir sight glasses, see-through coolant overflow containers, and coolant recovery containers.

Not quite. The answer is If you fail one part of the skills test, you'll have to retake the entire test next time.

Applicants fail the pre-trip inspection more than any other part of the CDL skills test. There's a lot to remember, and you may not be allowed to take a pre-trip inspection checklist or any other "cheat sheet" with you to the test. You will be provided with an official checklist you can use. Inspecting your vehicle in the same order each time will help you remember the steps both for your skills test and in your commercial driving career. If you fail any part of the skills test, you will have to take the entire skills test again and pay additional fees.

Not quite. The answer is So no one drives the vehicle while you are inspecting under it.

Take the starter key with you during the inspection so no one can drive your vehicle while you are inspecting under it.

Not quite. The answer is All of the above

The external lights that should be checked include the following: high- and low-beam headlights, clearance lights, taillights, backing lights, four-way emergency flashers, left and right turn signals, red and amber reflectors, and brake lights.

Not quite. The answer is Oil level

Use the dipstick to check the oil level in the engine. If the oil level is below the refill mark, add oil before you start to drive.

Not quite. The answer is do all of the above.

As part of your vehicle inspection test, if your vehicle is equipped with a cargo lift, explain how to check it for correct operation. Check for leaking, damaged, or missing parts. Also check that the cargo lift is fully retracted and securely latched.

Not quite. The answer is Neither of the above

The drag link and Pitman arm are two components of the steering system.

Not quite. The answer is Both of the above are true.

Your vehicle must not be driven if one-fourth or more of the leaves in a leaf spring are missing or broken. However, any defect in the leaf springs is potentially dangerous. A brake drum that is cracked more than halfway across must be replaced.

Not quite. The answer is Hydraulic brakes

If your vehicle has hydraulic brakes, test them by pumping the brake pedal three times and then applying firm pressure to it for five seconds, making sure the pedal does not move during that time. If your vehicle has air brakes, test them by performing the final air brake check as described in the Arkansas Commercial Driver License Manual.

Not quite. The answer is battery

During your pre-trip inspection, check the battery to make sure that its connections are tight and not excessively corroded. Also check that the door or cover of the battery box is secure and undamaged.

Not quite. The answer is Over the trailer bumper; hooks face downward

During your pre-trip inspection, make sure that the safety chains are crossed (if they are long enough for that). Make sure that the safety chains are hooked over the trailer bumper and onto the trailer so that the hooks face downward.

Not quite. The answer is In your pocket

While you are performing the pre-trip inspection, you do not want someone (such as a co-driver) who is unaware of your location to start your vehicle and accidentally injure you. Make sure you have the ignition key with you as you perform the inspection.

Not quite. The answer is Drive shaft

The drive shaft transmits torque from the transmission and the gear box to the drive wheels. During your pre-trip inspection, check that the drive shaft is not bent or cracked and the U-joints aren't loose or worn. A dropped drive shaft while you're driving could be very serious.

Not quite. The answer is Release arm

The release arm allows you to disengage the fifth-wheel locking jaws so you can uncouple the trailer. During your pre-trip inspection, check that the release arm is in the engaged position and the safety latch (if so equipped) is in place.

Not quite. The answer is Non-steering axle tires

Steering axle tires must have a tread depth of at least 4/32 inch. All other tires must have a tread depth of at least 2/32 inch.

Not quite. The answer is Brake drum / linings

Brake linings use friction to turn the vehicle's kinetic energy into heat. However, excessive heat from overuse of the brakes may cause the brake linings to wear out faster, leading to brake fade or failure. Also, if one brake is out of adjustment and can't do its job, the other brakes will have to work harder, causing them to overheat.

Not quite. The answer is Check that the steps leading to the cab entry are solid, clear of objects, and securely bolted to the frame.

During the in-cab inspection, shift into neutral (for a manual) or park (for an automatic) and make sure the parking brake is on. Start the engine and listen for unusual noises. (You do inspect the steps to the cab during the pre-trip inspection, but not during the in-cab part of the inspection.)