Alaska CDL: Double & Triple Trailers Practice Test

Not quite. The answer is closed.

To uncouple the second trailer, start by applying the parking brakes to keep your vehicle from moving. Lower the landing gear of the second trailer. Close the shut-off valves at the rear of the first trailer (and on the dolly if so equipped) to keep air from going out of the vehicle. Then disconnect the dolly air and electric lines, release the dolly brakes, and release the dolly fifth wheel latch. You are now ready to pull the first trailer and the dolly away from the second trailer.

Not quite. The answer is you couple the third trailer to the second trailer before you couple them to the first trailer.

A triple combination vehicle has four units (not counting the converter dollies): a tractor and three trailers. You couple a triple as follows: 1. Couple the first trailer to the tractor the same way that you couple any combination vehicle. 2. Couple the third trailer to the second trailer using the method for coupling doubles (which will involve the use of a converter dolly). 3. Move another converter dolly into position. 4. Couple the tractor and first trailer to the second and third trailer using the method for coupling doubles (which will involve another converter dolly).

Not quite. The answer is An additional drawbar

The type of converter dolly described in your official state CDL manual is an A-dolly. It has a single drawbar, whose eye fits over the pintle hook in the rear of a semitrailer. The A-dolly can pivot or articulate on that pintle hook. In contrast, a B-dolly (or C-dolly) has two drawbars, each with its own eye. These fit over two pintle hooks in the rear of a trailer. These two connections prevent the B-dolly from pivoting on the pintle hooks, thus eliminating one articulation or pivot point. B-dollies are used to connect B-doubles (also called B-train doubles).

Not quite. The answer is fifth; one or two

A semitrailer can be connected to a converter dolly because, like the rear of a typical tractor, it has a fifth wheel and one or two axles.

Not quite. The answer is Pull against the rear semitrailer's pin.

To check the coupling of the rear semitrailer, pull against the pin holding the rear semitrailer. Never drive your vehicle until you are sure that all trailers are properly coupled.

Not quite. The answer is Check your mirrors to keep an eye on your tires.

Use the mirrors to keep an eye on your tires. It's one way to spot a tire fire. But your mirrors don't eliminate all blind spots. Your truck still has large blind spots, often called No-Zones.

Not quite. The answer is do both of the above.

In bad weather or mountain driving or on slippery roads, use extreme caution. When you drive a double or triple, you're pulling a lot of dead axles with just a few drive axles. This increases the chance of loss of traction, causing a skid. Also, rearward amplification makes the rearmost trailer much more prone to rolling over. Drive slowly around curves and turns and avoid sudden moves.

Not quite. The answer is A truck has less traction when it's empty than when it's fully loaded.

Trucks that are empty or only lightly loaded take longer to stop because the stiff suspension springs and strong brakes give poor traction and make it easier to lock the wheels.

Not quite. The answer is foot pedal.

The trailer hand valve (also called the Trolley Valve or Johnson Bar) operates only the trailer brakes, not the tractor brakes. Hence, use it only when you want to test the trailer brakes. Don't use it in normal driving because braking the trailers and not the tractor can cause a trailer to skid. The foot brake sends air to all the brakes on the vehicle – the tractor and all trailers. There is much less danger of causing a skid or jackknife when using just the foot brake.

Not quite. The answer is 20 to 45 psi.

The tractor protection valve keeps air in the tractor or truck brake system should the trailer break away or develop a bad leak. The tractor protection valve is designed to close automatically when the air pressure falls into the range specified by the manufacturer, typically 20–45 psi.

Not quite. The answer is apply light pressure on the brakes.

Avoid driving through deep puddles or flowing water if possible. If not, slow down and downshift into a low gear. Gently press on the brakes and maintain pressure for a short distance when you are out of the water. This will heat up the brakes and dry them out. (However, don't overdo it, or the brakes may overheat.) Then apply the brakes to make a test stop when it is safe to do so.

Not quite. The answer is Both (a) and (b)

Take special care when pulling two or three trailers. In bad weather, under slippery conditions, and in mountain driving, you must be especially careful. There is a greater risk of skids and loss of traction. Also, doubles and triples need more space because they can’t be turned or stopped suddenly. Maintain a greater following distance. Make sure you have large enough gaps before entering or crossing traffic.

Not quite. The answer is Allow a greater following distance than for smaller commercial vehicles.

Doubles and triples need more space because they can’t be turned or stopped suddenly. Allow a greater following distance behind the vehicle in front of you.

Not quite. The answer is open the shut-off valves at the rear of the first trailer and close the shut-off valves at the rear of the second trailer.

Air must travel through the air lines of the tractor and all trailers – and that's all. Open the shut-off valves at the rear of each trailer but the last one to enable the air to travel to the trailer behind it. Close the shut-off valves at the rear of the last trailer to keep air from escaping.

Not quite. The answer is Neither of the above will cause it.

Despite what footnote 5 in 49 CFR 393.11 says, Operational Policy 15 of the North American Standard Out-of-Service Criteria states that a converter dolly must have one stop lamp, one tail lamp, and (if the dolly obscures the tractor's rear turn signals) turn signal lights, but only when the dolly is being towed singly and is not towing a trailer. In a full multi-trailer configuration, the rearmost trailer must have working stop lights and taillights, of course.

Not quite. The answer is Either (a) or (b)

Federal regulation 49 CFR 380.205 states that you must meet various requirements before you can start training to operate a triple long combination vehicle. These requirements include 6 months' immediately prior experience driving either a tractor/semi-trailer combination or a tractor/semi-trailer/trailer combination, with a gross combination weight rating (GCWR) of at least 26,001 pounds.

Not quite. The answer is step on and off the brake pedal several times.

To test the tractor protection valve, charge the trailer air brake system, turn off the engine, and lower the air pressure by stepping on and off the brake pedal several times. The tractor protection valve control (also called the trailer air supply control) should pop out (or go from the “normal” to the “emergency” position) when the air pressure falls into the range specified by the manufacturer (typically 20–45 psi).

Not quite. The answer is use controlled or stab braking.

Hard braking and turning at the same time is likely to cause a skid. You should brake in a way that will keep your vehicle in a straight line and allow you to turn if necessary. If you need to brake suddenly to avoid a crash, use controlled braking or stab braking (but don't use stab braking if your vehicle has antilock brakes).

Not quite. The answer is slightly raised.

To test the coupling of the dolly to the second trailer, you'll pull the tractor forward so the dolly will pull against the kingpin of the second trailer. Before doing so, raise the trailer's landing gear slightly. This will prevent damage if the trailer moves, and prevent the trailer from falling onto the ground if the dolly pulls away from the trailer.

Not quite. The answer is the rear trailer of a triple.

In a double or triple combination, each trailer is more likely to roll over than the one in front of it. The rear trailer of a triple is 3.5 times as likely to roll over as a five-axle tractor-trailer. This is known as rearward amplification or the "crack-the-whip effect." For safety, position the heaviest trailer in front and the lightest trailer in the rear.