New Mexico CDL: Double & Triple Trailers Practice Test

Not quite. The answer is 2

In this context, articulation or pivoting means movement between two units separated by a joint, such as between a tractor and a trailer. The standard or STAA doubles described in your official state CDL handbook are connected with an A-dolly, which has a single drawbar connected to the front trailer. However, a B-double (also called a B-train double) has a two-drawbar B-dolly (or C-dolly), which is connected to two hitches in the front trailer. The two drawbar connections prevent this type of dolly from pivoting on the front trailer. The rear trailer connects to the dolly's fifth wheel. Hence, the only two pivot points are the tractor's fifth wheel and the B-dolly's fifth wheel. B-trains are legal in parts of Michigan and Washington State.

Not quite. The answer is to lower its landing gear.

After you have uncoupled the rear trailer from the converter dolly, you need to uncouple the converter dolly from the front trailer. You do this as follows: 1. Lower the landing gear of the dolly. 2. Disconnect the safety chains. 3. Apply the dolly's spring brakes or chock its wheels to keep the dolly from moving. 4. Release the pintle hook connecting the dolly to the trailer ahead of it. 5. Slowly pull clear of the dolly.

Not quite. The answer is The rig may jackknife.

Check your mirrors to monitor your trailers and see if a trailer has begun to skid. Do this every time you have to brake hard. Once the wheels of a trailer begin to skid, the risk of jackknifing is high. Once the trailer swings out of your lane completely, you may not be able to prevent a jackknife.

Not quite. The answer is a coupling device that connects a semitrailer to the rear of a tractor-trailer.

The converter dolly connects a semitrailer to the rear of a tractor-trailer, forming a double or triple combination.

Not quite. The answer is slightly raised.

To test the coupling of the dolly to the second trailer, you'll pull the tractor forward so the dolly will pull against the kingpin of the second trailer. Before doing so, raise the trailer's landing gear slightly. This will prevent damage if the trailer moves, and prevent the trailer from falling onto the ground if the dolly pulls away from the trailer.

Not quite. The answer is There are more critical parts to check.

There is nothing inherently wrong with double or triple trailers. There are just more critical parts to check. For a triple, you must check the critical parts of three trailers and two converter dollies, problems in any of which can cause serious trouble.

Not quite. The answer is using the dolly's parking brake control.

To connect the converter dolly to the first semitrailer, release the dolly's brakes so it can be moved. You release the dolly's brakes by opening the air tank petcock (valve) or using the dolly's parking brake control if the dolly is equipped with spring brakes.

Not quite. The answer is Never

Older vehicles may be equipped with manual front-wheel limiting valves. A control in the cab allows the driver to cut air pressure to the front brakes in half. It was thought that doing this would help reduce front-wheel skids on slippery roads. According to the CDL manual, however, more recent tests have shown that front-wheel braking is safe even on icy roads. Federal regulations now prohibit manual front-wheel limiting valves in vehicles manufactured since March 1, 1975. Automatic ratio valves, which limit front-axle braking only when brake applications are approximately 60 psi or less, are still permitted. These valves cannot be controlled manually by the driver. Note: The advent of antilock brakes (ABS) may make automatic ratio valves less useful as well.

Source: 49 CFR § 393.48

Not quite. The answer is slightly raised.

When connecting the rear trailer to the converter dolly, lock the trailer brakes and raise the trailer landing gear slightly off the ground so it won't be damaged if the trailer moves. Then pull forward with the trailer brakes still locked, to check that the rear trailer is locked onto the converter dolly. If it's not, at least the landing gear will keep the rear trailer from falling onto the ground.

Not quite. The answer is The more sharply you turn, the greater the chances of a skid or rollover.

Don't turn any more than needed to clear whatever is in your way. The more sharply you turn, the greater the chances of a skid or rollover.

Not quite. The answer is A truck has less traction when it's empty than when it's fully loaded.

Trucks that are empty or only lightly loaded take longer to stop because the stiff suspension springs and strong brakes give poor traction and make it easier to lock the wheels.

Not quite. The answer is air escape from the open valve.

Test the trailer brakes by opening the service line valve at the rear of the rig. You should hear the telltale hiss of air escaping. If you don't, it means that air is not flowing through the entire line, and you will need to investigate.

Not quite. The answer is Some do; some don't.

All converter dollies built since 1975 are required to have spring brakes. Older converter dollies that don't have spring brakes have emergency air brakes, which work from the air stored in the trailer air tank.

Not quite. The answer is a yellow lamp on the left side.

A converter dolly with antilock brakes is required to have a yellow ABS lamp on its left side. All converter dollies built since March 1, 1998 have antilock brakes.

Not quite. The answer is closed.

To uncouple the second trailer, start by applying the parking brakes to keep your vehicle from moving. Lower the landing gear of the second trailer. Close the shut-off valves at the rear of the first trailer (and on the dolly if so equipped) to keep air from going out of the vehicle. Then disconnect the dolly air and electric lines, release the dolly brakes, and release the dolly fifth wheel latch. You are now ready to pull the first trailer and the dolly away from the second trailer.

Not quite. The answer is closed.

A pre-trip inspection of a double or triple combination vehicle includes an inspection of each converter dolly in the vehicle. Among other things, check that the converter dolly air tank drain valve is closed.

Not quite. The answer is Check for normal air pressure. Release the parking brakes. Pull forward slowly. Apply the trailer brakes, using the hand control if so equipped.

Checking your trailer's service brakes is a four-step process: 1. Check for normal air pressure. 2. Release the parking brakes. 3. Pull your vehicle forward slowly. 4. Apply the trailer brakes, using the hand control (trolley valve) if so equipped. If the trailer brakes are properly connected and working, you should feel them come on at this point.

Not quite. The answer is enough to remove some of the trailer's weight from the converter dolly.

Lower the landing gear of the second semitrailer enough to remove some of the trailer's weight from the converter dolly. This will make it easier to pull the dolly out from under the trailer.

Not quite. The answer is The dolly tow bar may fly up.

If you unlock the pintle hook while the dolly is still underneath the rear trailer, the dolly's tow bar may fly up, making it harder to recouple and possibly injuring someone.

Not quite. The answer is Charge the trailer's air tank and then disconnect the emergency air line.

If the second trailer doesn’t have spring brakes, drive the tractor close to the trailer, connect the emergency line, charge the trailer air tank, and disconnect the emergency air line. This will set the trailer emergency brakes (assuming the slack adjusters are correctly adjusted). Chock the wheels if you have any doubt about the brakes.