Montana CDL: Pre-Trip Inspection Practice Test

Not quite. The answer is Tandem release arm / locking pins

If so equipped, make sure that the locking pins are locked in place and the release arm is secured.

Not quite. The answer is Doors

During your pre-trip inspection, check that the doors to your vehicle are undamaged and that they open and close properly from the outside. The hinges should be secure with seals intact. Note: If you're inspecting a passenger vehicle, there are additional checks you should perform on the passenger entry doors and the emergency exit doors.

Not quite. The answer is Catwalk

Check that the steps leading up to the cab and catwalk (if any) are clear of obstructions and secured to the tractor frame.

Not quite. The answer is slack adjusters.

The slack adjuster connects to the pushrod. If the slack adjuster has too much slack, the brake can fail.

Not quite. The answer is seals

Damaged door seals allow drafts or rain to get inside. Check if the door seals are intact and undamaged. Replace any leaky door seals.

Not quite. The answer is Both of the above

There are many things you must check during your pre-trip inspection. In Step 5 (Walkaround Inspection) of the Seven-Step Inspection Method, you'll check many items around the vehicle, including the cargo securement and the condition of the windshield wipers.

Not quite. The answer is Fire extinguisher

Federal regulations require CMVs to carry a properly rated fire extinguisher and warning devices for stopped vehicles. Spare electrical fuses are no longer federally required, although they are still recommended if the vehicle uses fuses. First-aid kits and wheel chocks may be required by some employers or states, but they are not federally required for all CMVs.

Source: 49 CFR 393.95

Not quite. The answer is the service brake

To test the service brakes, pull forward at 5 mph and then apply the service brake. Unless the brakes are wet, they should apply evenly and not pull the vehicle to one side or the other. If your vehicle pulls to one side or the other, the service brakes may need repair.

Not quite. The answer is When you start the engine, the oil temperature gauge should climb to the normal operating range.

When you start the engine, the oil temperature gauge should begin a gradual rise to the normal operating range. (The oil may take longer than the coolant to warm up.) If the gauge doesn't rise, the oil temperature sensor may have failed.

Not quite. The answer is Seats

In a passenger vehicle, the seats must be safe for passengers to sit in. During your pre-trip inspection, check that the seats are firmly attached to the floor. Make sure that the seatbacks and frames are not broken. Check that the seat cushions are securely attached to the seat frames and are in satisfactory condition.

Not quite. The answer is leaking fluids.

A drum brake isn't designed to contain fluid. Note, however, that grease or oil can seep onto the brake linings or pads from a leak elsewhere. If the lining or pad appears to be soaked in oil or grease, replace it and look for a leak elsewhere.

Not quite. The answer is Frame

The frame consists of the structural members for supporting the body of the vehicle or trailer. When inspecting the frame, (1) check for cracks; (2) check for broken welds; and (3) check for illegal holes or other damage to the longitudinal frame members, cross members, box, or floor.

Not quite. The answer is Pitman arm

The Pitman arm is attached to the output shaft of the steering box. The Pitman arm changes the rotation of the output shaft into back-and-forth movement, which is used to turn the front wheels of the CMV. The torque arm (also known as a radius rod) and bearing plate are parts of a vehicle's suspension.

Not quite. The answer is Lug nuts

During your pre-trip inspection, check that all lug nuts are present and accounted for, tightly fastened, and free of cracks or distortions.

Not quite. The answer is Drive shaft

The drive shaft transmits torque from the transmission and the gear box to the drive wheels. During your pre-trip inspection, check that the drive shaft is not bent or cracked and the U-joints aren't loose or worn. While you're driving, a dropped drive shaft could be very serious.

Not quite. The answer is Oil level

Use the dipstick to check the oil level in the engine. If the oil level is below the refill mark, add oil before you start to drive.

Not quite. The answer is the support frame.

As part of your vehicle inspection test, if your vehicle has a semitrailer, you will have to check the landing gear. Check that it is fully raised and no parts are missing. Check that the crank handle is secure and the support frame is undamaged. If the landing gear is power operated, check for air or hydraulic leaks.

Not quite. The answer is Exhaust

Your vehicle's exhaust system consists of a set of pipes and other components for removing the hot combustion gases produced by your engine. One of these gases, carbon monoxide (CO), can be particularly poisonous to you if an exhaust leak causes CO to build up in the cab. During your pre-trip inspection, check the exhaust system for cracks, holes, and severe dents. Check for sounds and signs of leaks. There should be no loose, broken, or missing parts. No exhaust system parts should be rubbing against fuel system parts, tires, wires, air lines, or other moving parts of the vehicle.

Not quite. The answer is Both of the above are true.

Your vehicle must not be driven if one-fourth or more of the leaves in a leaf spring are missing or broken. However, any defect in the leaf springs is potentially dangerous. A brake drum that is cracked more than halfway across must be replaced.

Not quite. The answer is Steering linkage

The steering gearbox (also called the steering box) is connected to the steering column. The steering linkage transmits steering action from the steering box to the front wheels. This linkage includes the Pitman arm, drag link, tie rod, and upper and lower steering knuckles. During your pre-trip inspection, check that these components are securely mounted. Check for loose or missing nuts, bolts, or cotter pins. Check that nothing is wrapped around the tie rod.