Michigan CDL: Pre-Trip Inspection Practice Test

Not quite. The answer is Frame

The frame consists of the structural members for supporting the body of the vehicle or trailer. When inspecting the frame, (1) check for cracks; (2) check for broken welds; and (3) check for illegal holes or other damage to the longitudinal frame members, cross members, box, or floor.

Not quite. The answer is Check the sight glass.

Your vehicle may provide a way for you to check the coolant level even when the engine is hot. Such devices include reservoir sight glasses, see-through coolant overflow containers, and coolant recovery containers.

Not quite. The answer is the special features of the vehicle.

Class B and Class C CDLs cover the operation of a wide variety of different types of vehicles with their own special features. You must perform the vehicle inspection test on a vehicle that is representative of the kinds of vehicles that you plan to drive professionally. As part of the test, you will have to inspect any special features of your vehicle (such as the special features of school buses if you're using one for the test).

Not quite. The answer is In your pocket

While you are performing the pre-trip inspection, you do not want someone (such as a co-driver) who is unaware of your location to start your vehicle and accidentally injure you. Make sure you have the ignition key with you as you perform the inspection.

Not quite. The answer is Rim

The rim is the outer part of the wheel, to which a tire is attached. A damaged rim can result in loss of the tire from the rim, loss of the wheel from the axle, loss of air pressure in the tire, or the wheel rolling off the rim because of damage to the flange. During your pre-trip inspection, check that the rim is undamaged and the flange isn't bent. Check that no welding repairs have been made to the rim. Finally, check that there are no rust trails (which might indicate that the rim is loose on the wheel).

Not quite. The answer is If you fail one part of the skills test, you'll have to retake the entire test next time.

Applicants fail the pre-trip inspection more than any other part of the CDL skills test. There's a lot to remember. Inspecting your vehicle in the same order each time will help you remember the steps both for your skills test and in your commercial driving career. If you fail any part of the skills test, you will have to take the entire skills test again and pay additional fees.

Not quite. The answer is Neither of the above

The drag link and Pitman arm are two components of the steering system.

Not quite. The answer is Leaks

As part of your engine inspection, check the ground below the engine compartment for puddles or dripping liquids.

Not quite. The answer is any of the above

When you check the engine compartment, make sure the engine is off. In this step, you check a number of things, including checking the air compressor, water pump, and hoses for leaks.

Not quite. The answer is Locking pins

If so equipped, look for loose or missing locking pins in the slide mechanism of the sliding fifth wheel. Make sure that the pins are fully engaged.

Not quite. The answer is Steering axle tires

The tires on the steering axle should have at least 4/32 inch of tread, and all other tires should have at least 2/32 inch of tread. Inadequate tread on the front tires increases the risk of a front-wheel skid.

Not quite. The answer is 1/8 full.

According to the CDL manual, the DEF tank should be more than 1/8 full. (Typically, a vehicle uses about 1 gallon of DEF for every 50 gallons of diesel fuel.) Also check the DEF indicator on the dashboard to be sure it is working properly.

Not quite. The answer is remove the radiator cap if the engine might be hot.

If the engine is cool to the touch of your bare hand, you can probably remove the radiator cap and check the coolant level safely. If the engine is hot, do NOT remove the radiator cap; it's dangerous. If there is a sight glass or coolant reservoir, you can use it to check the coolant level. Otherwise, just tell the examiner how you would check the coolant level by removing the radiator cap once the engine is cool.

Not quite. The answer is Fire extinguisher and warning devices for stopped vehicles

Federal regulations require every CMV to carry one of the following sets of warning devices in case the driver must stop the CMV on the road: three reflective triangles and a fire extinguisher. Spare electrical fuses are no longer federally required emergency equipment under current FMCSA regulations. States may require extra emergency equipment on certain vehicles.

Source: 49 CFR 393.95

Not quite. The answer is the parking brake

The parking brake is meant to keep your vehicle from moving. The best way to test it is to apply the brake and then try to pull forward gently. The parking brake should hold your vehicle in place.

Not quite. The answer is Oil pressure

During your pre-trip inspection, make sure that the oil pressure gauge is working and it shows normal or increasing oil pressure. Running the engine without oil will eventually cause serious damage.

Not quite. The answer is Over the trailer bumper; hooks face downward

During your pre-trip inspection, make sure that the safety chains are crossed (if they are long enough for that). Make sure that the safety chains are hooked over the trailer bumper and onto the trailer so that the hooks face downward.

Not quite. The answer is the coupling system.

A Class A CDL allows you to pull a trailer whose gross vehicle weight rating (GVWR) exceeds 10,000 pounds. Thus, you must know how a trailer is coupled to a tractor. The Class A vehicle inspection test will evaluate your ability to inspect the coupling system.

Not quite. The answer is you'll fail the entire CDL skills test.

If your vehicle is equipped with air brakes but you fail to check them correctly, you'll fail the vehicle inspection portion of your CDL skills test (and therefore, the entire skills test).

Not quite. The answer is Lug nuts

During your pre-trip inspection, check that all lug nuts are present and accounted for, tightly fastened, and free of cracks or distortions.