Illinois CDL: Double & Triple Trailers Practice Test

Not quite. The answer is If there are vehicles on both sides of you, a move to the right may still be best.

To avoid a head-on collision, steer right toward the shoulder or curbline. Even if you are blocked on both sides by other vehicles, a move to the right may still be best. At least you won't force other drivers into an opposing traffic lane, possibly involving them in a head-on collision. Prepare to drive entirely off the roadway to the right if necessary to avoid a head-on collision. Head-on collisions are often fatal.

Not quite. The answer is the shut-off valves, the converter dolly or dollies, and the air brakes on all trailers.

To inspect a double or triple, first inspect it just as you would inspect any combination vehicle. Then check that the shut-off valves are open on all trailers but the last trailer. Check each converter dolly to be sure that the pintle hook is properly latched.

Not quite. The answer is Use the engine brake or speed retarder.

A retarder supplements the braking force on the drive wheels. On a slippery surface, this may cause the wheels to lock, resulting in a skid. Turn off your retarder when driving on wet, icy, or snowy roads. Instead, slow down, increase your following distance, and try to brake gently.

Not quite. The answer is Rocky Mountain double

A double pup trailer consists of two 28.5-foot trailers, known as "pup trailers." A double pup trailer is also known as an STAA trailer, named for the Surface Transportation Assistance Act (STAA). This standard-double configuration is the only type of double trailer that is allowed nationwide. A Rocky Mountain double trailer consists of a 40- to 53-foot trailer followed by a 28.5-foot pup trailer. Rocky Mountain doubles are allowed in certain Western states. A turnpike double trailer consists of two 48-foot trailers. Turnpike doubles can be found traveling on expressways in the Eastern states.

Not quite. The answer is less

Double and triple vehicles are more prone to rolling over or jackknifing than single vehicles are. Avoid sudden braking or steering changes. Look far enough ahead that you can slow down or change lanes gradually when necessary.

Not quite. The answer is may have poor traction due to bouncing and wheel lockup.

Trucks brake best when they are used as they were designed: to carry a properly balanced load. Empty trucks actually have longer stopping distances than loaded trucks because they have less traction.

Not quite. The answer is 3

In this context, articulation or pivoting means movement between two units separated by a joint, such as between a tractor and a trailer. The standard or STAA double combination in the CDL handbook has 3 points of articulation: (1) the fifth wheel of the tractor; (2) the pintle hook of the front trailer; (3) the fifth wheel of the converter dolly.

Not quite. The answer is the trailer will be raised slightly when the converter dolly is backed under it.

To connect the rear trailer to the converter dolly, the trailer must be at the right height. It should be slightly lower than the center of the dolly's fifth wheel so that the trailer will be raised slightly when the dolly is pushed underneath it.

Not quite. The answer is a separate air tank.

Federal regulations require brakes on every wheel of a combination vehicle, including the wheels of the semitrailers and converter dollies. Like semitrailers, dollies have their own air brakes and their own air tanks.

Source: 49 CFR § 393.42

Not quite. The answer is An additional drawbar

The type of converter dolly described in your official state CDL manual is an A-dolly. It has a single drawbar, whose eye fits over the pintle hook in the rear of a semitrailer. The A-dolly can pivot or articulate on that pintle hook. In contrast, a B-dolly (or C-dolly) has two drawbars, each with its own eye. These fit over two pintle hooks in the rear of a trailer. These two connections prevent the B-dolly from pivoting on the pintle hooks, thus eliminating one articulation or pivot point. B-dollies are used to connect B-doubles (also called B-train doubles).

Not quite. The answer is 20 to 45 psi.

The tractor protection valve keeps air in the tractor or truck brake system should the trailer break away or develop a bad leak. The tractor protection valve is designed to close automatically when the air pressure falls into the range specified by the manufacturer, typically 20–45 psi.

Not quite. The answer is the tractor protection valve control (trailer air supply control) will pop out or go from "normal" to "emergency."

When you test the tractor protection valve, the tractor protection valve control (also called the trailer air supply control) should pop out or go from the "normal" to the "emergency" position. This shows that the tractor protection valve has closed automatically to keep the air pressure from falling too far.

Not quite. The answer is a yellow lamp on the left side.

A converter dolly with antilock brakes is required to have a yellow ABS lamp on its left side. All converter dollies built since March 1, 1998 have antilock brakes.

Not quite. The answer is Allow a greater following distance than for smaller commercial vehicles.

Doubles and triples need more space because they can’t be turned or stopped suddenly. Allow a greater following distance behind the vehicle in front of you.

Not quite. The answer is foot pedal.

You can use the trailer hand valve (also known as a spike or Johnson bar) to test the trailer service brakes. During normal driving, however, all the service brakes on your vehicle are controlled with the foot pedal, which applies air to the service brakes at all the wheels.

Not quite. The answer is Some do; some don't.

All converter dollies built since 1975 are required to have spring brakes. Older converter dollies that don't have spring brakes have emergency air brakes, which work from the air stored in the trailer air tank.

Not quite. The answer is The more sharply you turn, the greater the chances of a skid or rollover.

Don't turn any more than needed to clear whatever is in your way. The more sharply you turn, the greater the chances of a skid or rollover.

Not quite. The answer is Uncouple the third semitrailer from the second dolly.

To couple a triple-trailer combination, you couple the tractor and first semitrailer to the second and third semitrailers. But to uncouple the triple-trailer combination, you start by just uncoupling the third semitrailer from the rest of the combination.

Not quite. The answer is A truck has less traction when it's empty than when it's fully loaded.

Trucks that are empty or only lightly loaded take longer to stop because the stiff suspension springs and strong brakes give poor traction and make it easier to lock the wheels.

Not quite. The answer is apply light pressure on the brakes.

Avoid driving through deep puddles or flowing water if possible. If not, slow down and downshift into a low gear. Gently press on the brakes and maintain pressure for a short distance when you are out of the water. This will heat up the brakes and dry them out. (However, don't overdo it, or the brakes may overheat.) Then apply the brakes to make a test stop when it is safe to do so.