Texas CDL: Tanker Vehicles Practice Test

Not quite. The answer is are bulk containers that are not permanently attached to a vehicle.

A portable tank is bulk packaging that is not permanently attached to a vehicle. The tank is loaded or unloaded while it is off the vehicle. Then the tank is put on the vehicle for transportation. Hence, the portable tank must show the owner or lessee's name. "Bulk packaging" means that the tank's capacity is more than 450 L (119 gallons) of liquid, or more than 454 kg (1,000 pounds) of gas. Some portable tanks have a capacity of 25,000 L (6,600 gallons).

Not quite. The answer is a high center of gravity.

It takes special skills to drive a tanker carrying liquid cargo because of the vehicle's high center of gravity and the possibility that the liquid cargo may surge forward and backward or from side to side. Much of a loaded tanker's weight is carried five or six feet above the ground. This makes a tanker top-heavy, which makes it more prone to rollovers than other types of vehicles. Tests have shown that a tank vehicle can roll over at the speed limits posted for curves. The safest way to take a curve in a tanker is to slow down well below the posted speed limit before you enter the curve.

Not quite. The answer is the front or the rear

Bulkheads help separate the load. When loading such tanks, distribute the weight evenly. Avoid putting too much weight on the front or the rear of the vehicle.

Not quite. The answer is 5 mph slower.

On a steep downgrade, don't keep applying your brakes continuously because this might cause them to fade (become less effective). Instead, apply your brakes sparingly as a supplement to engine braking. Select a "safe" speed. Let your vehicle reach this speed. Brake gently until you are going 5 mph slower. Then let your speed increase back to the "safe" speed. Keep varying your speed up and down this way. This technique is known as snub braking or snubbing.

Not quite. The answer is the top of the tank

In general, the Maximum Allowable Working Pressure (MAWP) of a pressurized tank is the maximum pressure that the weakest part of the tank can handle in normal operation. For a cargo tank on a motor vehicle, the federal definition of MAWP assumes that the weakest part is at the top of the tank.

Source: 49 CFR 178.320

Not quite. The answer is bulkheads.

Separators that divide a space into liquid-tight compartments are called bulkheads. The tank on a tanker vehicle may have bulkheads to divide the tank into separate compartments.

Not quite. The answer is 1,000 gallons or more.

Federal regulations define a "tank vehicle" as a commercial motor vehicle designed to transport liquids or gases within tanks that have an individual rated capacity of more than 119 gallons each and an aggregate rated capacity of 1,000 gallons or more. To drive such tank vehicles, you must have a Tank (N) endorsement or Combination Hazmat and Tank (X) endorsement on your CDL.

Source: 49 CFR § 383.5

Not quite. The answer is driving too fast.

Over-braking and over-steering can cause skids. Both over-braking and over-steering are more likely when you're driving too fast for the current road conditions.

Not quite. The answer is You should not load a cargo tank completely full.

Some liquids expand significantly when they warm up. To fill a tank with such a liquid, you must leave some room in the tank (called "outage") to take the expansion. Different liquids expand at different rates as the temperature increases. In science, the percentage increase of expansion for a given change in temperature is called the coefficient of thermal expansion. This value depends on the type of liquid. You need to find out how much outage you will need to allow for the type of liquid you'll be hauling.

Not quite. The answer is Within 500 feet behind the vehicle

If you park on the side of the road and the view of your vehicle is obscured by a hill or curve, place a reflective triangle far enough (up to 500 feet) behind your vehicle so it can be seen by other drivers.

Not quite. The answer is At the end of each working day

Oil and water can start to collect in the bottom of an air tank and can cause brake failure if it's not drained. Unless your vehicle automatically drains the air tanks, you should drain them at the end of each working day so the moisture and oil will not freeze or coagulate and cause your brakes to fail.

Not quite. The answer is your vehicle will stay in a straight line.

If you must brake in an emergency, brake in a way that keeps your vehicle in a straight line while still letting you turn if necessary. You can use the "controlled braking" method or (in a vehicle without antilock brakes) the "stab braking" method.

Not quite. The answer is Environment

The S.T.A.M.P.E.D. acronym is widely used to assist you in obtaining the correct hoses and fittings for your needs. S: the required size of the hose; T: the temperatures to which the hose will be subjected; A: the application (use) to which the hose will be put; M: the types of material (liquid, gas, etc.) that will have to flow through the hose; P: the maximum working pressure of the hose; E: the required fittings at the ends of the hose; D: the date at which the hose must be delivered to you.

Not quite. The answer is Before loading it, driving it, or unloading it

You should inspect a tank vehicle before loading it, driving it, or unloading it. This is to ensure that it is safe to carry out these activities and the vehicle can safely hold its liquid or gas contents.

Not quite. The answer is 9,000 gallons.

The average capacity of a DOT-406 or MC-306 fuel delivery truck (often called a "gasoline truck") is 9,000 gallons.

Not quite. The answer is There will be less front-to-back surge than there is in a tanker without baffles.

Baffled tanks have bulkheads with holes to reduce forward-and-backward surge. This will reduce the chance that forward surge will push your vehicle dangerously forward when you're slowing or stopping. However, these bulkheads don't significantly reduce side-to-side surge, so rollovers can still occur.

Not quite. The answer is both a hazardous materials (H) endorsement and a tank vehicle (N) endorsement.

A tank vehicle (N) endorsement qualifies you to haul liquids or gases. However, if those liquids or gases are classified as hazardous materials, you must also have a hazardous materials (H) endorsement to haul them. To obtain each of these endorsements, you must pass a specialized knowledge test. Note: These days, if you obtain both endorsements, your CDL may include the combined endorsement code X (tank vehicle and HazMat) instead of both H and N.

Not quite. The answer is may exceed legal weight limits.

A full tank of dense liquid (such as some acids) may exceed legal weight limits. For this reason, you may not be able to completely fill the tank with a dense liquid.

Not quite. The answer is MC-306 (DOT-406)

MC-306 (DOT-406) cargo tanks carry liquids under very low or no pressure (maximum allowable pressure of 3 psi for MC-306 and 4 psi for DOT-406). The cargo tank has an oval or elliptical cross section and is usually compartmented. These tanks are commonly used to carry gasoline, diesel fuel or fuel oil, and other flammable liquids.

Not quite. The answer is You should avoid backing whenever you can.

Backing up a large vehicle is always dangerous, even with a helper. Try to avoid backing up as much as possible.