Tennessee CDL: Double & Triple Trailers Practice Test

Not quite. The answer is may have poor traction due to bouncing and wheel lockup.

Trucks brake best when they are used as they were designed: to carry a properly balanced load. Empty trucks actually have longer stopping distances than loaded trucks because they have less traction.

Not quite. The answer is Some do; some don't.

All converter dollies built since 1975 are required to have spring brakes. Older converter dollies that don't have spring brakes have emergency air brakes, which work from the air stored in the trailer air tank.

Not quite. The answer is make things look smaller and farther away than they really are.

A convex mirror has a wider field of view than a flat mirror. However, objects viewed in a convex mirror look smaller and farther away. Remember this when you're trying to judge the distance of an object that you're viewing in a convex mirror.

Not quite. The answer is enough to take some of the weight off the dolly.

When uncoupling a loaded second or third semitrailer, lower the landing gear until it makes firm contact with the ground. Then crank the landing gear in low gear for a few more turns – just enough to lift some weight off the dolly, but not so much that you lift the trailer off the fifth wheel. This will make it easier to unlatch the fifth wheel now and couple the trailer next time.

Not quite. The answer is slow down.

You should always be able to stop within the distance you can see ahead. Your low-beam headlights let you see only about 250 feet ahead. At 55 mph, your vehicle will travel 250 feet in just 3.1 seconds – not enough time to notice and safely avoid a hazard that's within 250 feet of you. At 30 mph, your vehicle will travel 250 feet in 5.7 seconds.

Not quite. The answer is Use your mirrors to keep an eye on your tires.

Clean and adjust your mirrors as part of your pre-trip inspection, when your vehicle is parked. Adjust each mirror to show some part of your vehicle as well as the roadway. You can adjust your mirrors accurately only when your trailers are straight. While you're driving, use your mirrors to keep an eye on your tires. It's one way to spot a tire fire. However, no matter how carefully you adjust your mirrors, there will still be blind spots that your mirrors cannot show you.

Not quite. The answer is Check your mirrors to keep an eye on your tires.

Use the mirrors to keep an eye on your tires. It's one way to spot a tire fire. But your mirrors don't eliminate all blind spots. Your truck still has large blind spots, often called No-Zones.

Not quite. The answer is Use wheel chocks.

If the second trailer doesn’t have spring brakes, drive the tractor close to the trailer, connect the emergency line, charge the trailer air tank, and disconnect the emergency line. This will set the trailer emergency brakes (assuming the slack adjusters are correctly adjusted). However, if you have any doubt about the effectiveness of the trailer's braking system, chock the wheels.

Not quite. The answer is fifth; one or two

A semitrailer can be connected to a converter dolly because, like the rear of a typical tractor, it has a fifth wheel and one or two axles.

Not quite. The answer is Neither of the above will cause it.

Despite what footnote 5 in 49 CFR 393.11 says, Operational Policy 15 of the North American Standard Out-of-Service Criteria states that a converter dolly must have one stop lamp, one tail lamp, and (if the dolly obscures the tractor's rear turn signals) turn signal lights, but only when the dolly is being towed singly and is not towing a trailer. In a full multi-trailer configuration, the rearmost trailer must have working stop lights and taillights, of course.

Not quite. The answer is closed.

A pre-trip inspection of a double or triple combination vehicle includes an inspection of each converter dolly in the vehicle. Among other things, check that the converter dolly air tank drain valve is closed.

Not quite. The answer is Older models may lack spring brakes.

All converter dollies built since 1975 are required to have spring brakes. All converter dollies built since 1998 are required to have antilock brakes as well.

Not quite. The answer is air escape from the open valve.

Test the trailer brakes by opening the service line valve at the rear of the rig. You should hear the telltale hiss of air escaping. If you don't, it means that air is not flowing through the entire line, and you will need to investigate.

Not quite. The answer is 20 to 45 psi.

The tractor protection valve keeps air in the tractor or truck brake system should the trailer break away or develop a bad leak. The tractor protection valve is designed to close automatically when the air pressure falls into the range specified by the manufacturer, typically 20–45 psi.

Not quite. The answer is Allow much more space than is needed under ideal driving conditions.

The usual formula for following distance under ideal conditions is one second for every ten feet of vehicle length, plus an extra second if you are traveling at over 40 mph. The only thing the CDL manual says about following distance on slippery roads is that you should allow "much more space to stop." The Federal Motor Carrier Safety Administration (FMCSA) recommends doubling your usual following distance under poor driving conditions.

Source: "CMV Driving Tips - Following Too Closely," FMCSA, https://www.fmcsa.dot.gov/safety/driver-safety/cmv-driving-tips-following-too-closely

Not quite. The answer is step on and off the brake pedal several times.

To test the tractor protection valve, charge the trailer air brake system, turn off the engine, and lower the air pressure by stepping on and off the brake pedal several times. The tractor protection valve control (also called the trailer air supply control) should pop out (or go from the “normal” to the “emergency” position) when the air pressure falls into the range specified by the manufacturer (typically 20–45 psi).

Not quite. The answer is 2

In this context, articulation or pivoting means movement between two units separated by a joint, such as between a tractor and a trailer. The standard or STAA doubles described in your official state CDL handbook are connected with an A-dolly, which has a single drawbar connected to the front trailer. However, a B-double (also called a B-train double) has a two-drawbar B-dolly (or C-dolly), which is connected to two hitches in the front trailer. The two drawbar connections prevent this type of dolly from pivoting on the front trailer. The rear trailer connects to the dolly's fifth wheel. Hence, the only two pivot points are the tractor's fifth wheel and the B-dolly's fifth wheel. B-trains are legal in parts of Michigan and Washington State.

Not quite. The answer is leaks of air or hydraulic fluid

Check the landing gear as part of your walk-around inspection. Check that no parts are missing and it isn't bent or damaged. If the landing gear is power operated, check its hoses, fittings, and other parts for signs or sounds of escaping air or hydraulic fluid.

Not quite. The answer is more likely to turn over.

In a double or triple combination, each trailer is more likely to roll over than the one in front of it. The rear trailer of a triple is 3.5 times as likely to roll over as a five-axle tractor-trailer. This is known as the "crack-the-whip" effect, caused by rearward amplification. For safety, position the heaviest trailer in front and the lightest trailer in the rear.

Not quite. The answer is An additional drawbar

The type of converter dolly described in your official state CDL manual is an A-dolly. It has a single drawbar, whose eye fits over the pintle hook in the rear of a semitrailer. The A-dolly can pivot or articulate on that pintle hook. In contrast, a B-dolly (or C-dolly) has two drawbars, each with its own eye. These fit over two pintle hooks in the rear of a trailer. These two connections prevent the B-dolly from pivoting on the pintle hooks, thus eliminating one articulation or pivot point. B-dollies are used to connect B-doubles (also called B-train doubles).