Tennessee CDL: Combination Vehicles Practice Test

Not quite. The answer is Push in the trailer air supply valve control.

The control for the trailer air supply valve is an eight-sided red knob on the dashboard. You push the knob in to supply compressed air to the trailer air brake system. You pull the knob out to evacuate air from the trailer air brake system (which will set the trailer brakes).

Not quite. The answer is emergency

The tractor protection valve keeps air in the tractor if the trailer breaks away or develops a bad leak. If air pressure drops too low in the service line, the tractor protection valve will close. This stops air from escaping from the tractor and lets air out of the trailer emergency line, causing the trailer emergency brakes to come on.

Not quite. The answer is pushing in the trailer air supply control.

On newer vehicles, the trailer air supply control is an eight-sided red knob on the dashboard of the tractor. The knob may be labeled "Pull to exhaust...Push to supply" or something similar. When you push the knob in, air will flow through the trailer's emergency air lines to charge the trailer air brake system.

Not quite. The answer is the emergency and service air lines.

Before backing under the trailer, you must lock the trailer brakes – which means that you first have to make sure that the trailer brakes are working. Connect the emergency and service air lines and test the trailer brakes.

Not quite. The answer is To engage the trailer brakes in case of air pressure loss

The emergency air line has two main functions: (1) It supplies air to the trailer air tanks to keep the trailer brake system charged. (2) It controls the vehicle's emergency brakes. If air pressure in the emergency air line drops too low (say because of a bad leak or damage due to the trailer breaking loose), the trailer emergency brakes will come on. Also, the tractor protection valve will close to keep air from escaping from the tractor.

Not quite. The answer is On the left front or left rear corner

On a trailer, the yellow ABS malfunction lamp is located on the left front or left rear corner. Make sure you know where to look for it.

Not quite. The answer is Rear

The shut-off valve should be closed only at the rear of the last trailer so that air will flow to the brakes of all trailers but no farther.

Not quite. The answer is your brakes might fail.

On a combination vehicle, the brakes on the tractor and all trailers must work properly. If your combination vehicle is equipped with air brakes, check that air flows to all trailers and test both the trailer service brakes and the trailer emergency brakes.

Not quite. The answer is makes firm contact with the ground.

When uncoupling a loaded trailer, lower the landing gear until it makes firm contact with the ground. Then crank the landing gear in low gear for a few more turns – just enough to lift some weight off the tractor, but not so much that you lift the trailer off the fifth wheel. This will make it easier to unlatch the fifth wheel now and couple next time.

Not quite. The answer is Upper and lower fifth wheel, air lines, and electrical lines

When making a visual check of the coupling, be sure to check the upper and lower fifth wheel, air lines, and electrical lines.

Not quite. The answer is A 3-axle tractor towing two 27-foot trailers

When any vehicle turns, its rear wheels will follow a shorter path than its front wheels. This is called off-tracking or "cheating." The longer the vehicle, the greater the difference. In a combination vehicle, the trailer's wheels will off-track more than the tractor's rear wheels. In a double or triple combination vehicle, the wheels of the last trailer will off-track the most.

Not quite. The answer is secured but with enough slack for turns.

During your walk-around inspection, make sure that the electrical and air lines are secure but have enough slack to stay attached and secure even when the vehicle is turning.

Not quite. The answer is Turn wide as you complete the turn.

To turn right, you must turn wide to help prevent the rear end of your vehicle from overrunning the curb. However, if you swing wide to the left before you turn right, another driver may try to pass you on your right, which can lead to a collision. Instead, start the right turn with the rear of your vehicle as close to the curb as possible and then turn wide as you complete the turn. This will deny drivers room on the right to try to pass you.

Not quite. The answer is get away from your vehicle and call 911 or the posted emergency number.

A train traveling at 60 mph can take more than a mile to come to a complete stop. If your vehicle gets stuck on a railroad track, don't spend any time trying to free your vehicle. Get out of your vehicle and walk quickly at about a 45-degree angle to the tracks in the direction from which you expect trains to approach. That way, if your vehicle is hit, you won't be struck by flying debris. Call 911 or the telephone number on the railroad crossing sign for assistance.

Not quite. The answer is It will keep dirt and water out of the lines.

Some vehicles are equipped with "dead-end" or dummy couplers. When the air lines are not connected to a trailer, connect the glad hands to the dummy couplers to keep water and dirt out of the glad hands and air lines. If your vehicle doesn't have dummy couplers, you may be able to connect the glad hands to each other.

Not quite. The answer is Control line and signal line

The service air line is also known as the control line or signal line.

Not quite. The answer is Nothing is likely to happen until you try to apply the brakes.

If a leak has developed in the service line, air tank pressure may remain close to normal – until you try to brake. Then the air loss from the leak will cause the air pressure to drop quickly. If the air pressure drops far enough, the emergency brakes will come on.

Not quite. The answer is 4 psi per minute.

After the initial drop, the maximum acceptable leakage rates with the service brakes on are 3 psi per minute for single vehicles and 4 psi per minute for combination vehicles. If the leakage rate is higher, check for leaks and correct them.

Not quite. The answer is release the brakes.

Once you realize your vehicle is in a skid, you should release the brakes so that the wheels can grip the road again. The trailer will start to follow the tractor and straighten out.

Not quite. The answer is No, because the brakes on the trailer wheels caused the skid to begin with.

The trailer skid was caused by the brakes locking the wheels. Applying the trailer hand brake might make that even worse. Instead, release the brakes so the trailer wheels can roll again and regain traction.