New York CDL: Pre-Trip Inspection Practice Test

Not quite. The answer is While the parking brake is applied

The parking brake is meant to keep your vehicle from moving. The best way to test it is to apply the parking brake and then try to pull forward gently. The parking brake should hold your vehicle in place. If you're pulling one or more trailers, test each trailer's parking brakes in the same way.

Not quite. The answer is Ammeter or voltmeter

During your pre-trip inspection, check the ammeter gauge or voltmeter gauge to make sure that the alternator or generator is charging properly or the warning light is off.

Not quite. The answer is the trailer parking brake

Even after you release the truck or tractor parking brake, the trailer parking brake should still hold your vehicle in place when you try to pull forward gently.

Not quite. The answer is Doors

During your pre-trip inspection, check that the doors to your vehicle are undamaged and that they open and close properly from the outside. The hinges should be secure with seals intact. Note: If you're inspecting a passenger vehicle, there are additional checks you should perform on the passenger entry doors and the emergency exit doors.

Not quite. The answer is Exhaust

Your vehicle's exhaust system consists of a set of pipes and other components for removing the hot combustion gases produced by your engine. One of these gases, carbon monoxide (CO), can be particularly poisonous to you if an exhaust leak causes CO to build up in the cab. During your pre-trip inspection, check the exhaust system for cracks, holes, and severe dents. Check for sounds and signs of leaks. There should be no loose, broken, or missing parts. No exhaust system parts should be rubbing against fuel system parts, tires, wires, air lines, or other moving parts of the vehicle.

Not quite. The answer is air lines and electrical lines

During your pre-trip inspection, check the electrical lines and air hoses (or hydraulic hoses for hydraulic brakes). Make sure that the lines and hoses are not cut, chafed, spliced, or worn. Also make sure they are not tangled, pinched, or dragging on parts of the tractor.

Not quite. The answer is When you start the engine, the oil temperature gauge should climb to the normal operating range.

When you start the engine, the oil temperature gauge should begin a gradual rise to the normal operating range. (The oil may take longer than the coolant to warm up.) If the gauge doesn't rise, the oil temperature sensor may have failed.

Not quite. The answer is If you fail one part of the skills test, you'll have to retake the entire test next time.

Applicants fail the pre-trip inspection more than any other part of the CDL skills test. There's a lot to remember, and you may not be allowed to take a pre-trip inspection checklist or any other "cheat sheet" with you to the test. Inspecting your vehicle in the same order each time will help you remember the steps both for your skills test and in your commercial driving career. If you fail any part of the skills test, you will have to take the entire skills test again and pay additional fees.

Not quite. The answer is the windshield wipers and washer

Check that the windshield wiper blades are in good condition and press hard enough against the windshield to keep it clean without excessive streaking. Also make sure that the windshield washer mechanism works and there is enough windshield washer fluid in the reservoir.

Not quite. The answer is Non-steering axle tires

Steering axle tires must have a tread depth of at least 4/32 inch. All other tires must have a tread depth of at least 2/32 inch.

Not quite. The answer is slack adjusters.

The slack adjuster connects to the pushrod. If the slack adjuster has too much slack, the brake can fail.

Not quite. The answer is Spacers

Wheel spacers adjust wheel offset. During your pre-trip inspection, inspect each wheel that has wheel spacers to make sure that no spacers are missing, bent, damaged, or rusted through. Make sure that dual tires aren't touching. Dual tires that touch can catch fire.

Not quite. The answer is Turn signals

There are five dash indicators that you should ensure are working correctly: the left turn signal, the right turn signal, the four-way emergency flashers, the high beams, and the indicator for the anti-lock braking system (if your vehicle is so equipped).

Not quite. The answer is Seats

In a passenger vehicle, the seats must be safe for passengers to sit in. During your pre-trip inspection, check that the seats are firmly attached to the floor. Make sure that the seatbacks and frames are not broken. Check that the seat cushions are securely attached to the seat frames and are in satisfactory condition.

Not quite. The answer is Hydraulic brakes

If your vehicle has hydraulic brakes, test them by pumping the brake pedal three times and then applying firm pressure to it for five seconds, making sure the pedal does not move during that time. If your vehicle has air brakes, test them by performing the final air brake check as described in the New York State Commercial Driver's Manual.

Not quite. The answer is Check the sight glass.

Your vehicle may provide a way for you to check the coolant level even when the engine is hot. Such devices include reservoir sight glasses, see-through coolant overflow containers, and coolant recovery containers.

Not quite. The answer is Release arm

The release arm allows you to disengage the fifth-wheel locking jaws so you can uncouple the trailer. During your pre-trip inspection, check that the release arm is in the engaged position and the safety latch (if so equipped) is in place.

Not quite. The answer is 10

If there is more than 10 degrees of play in your steering wheel, your vehicle will be harder to steer. Have the problem corrected before you drive the vehicle. Ten degrees is equivalent to about 1¾ inches at the rim of a 20-inch steering wheel. According to federal regulations, there must not be more than 2½ inches of play at the rim of a 20-inch steering wheel.

Source: 49 CFR 570.60

Not quite. The answer is Splash guards

Splash guards (mud flaps) behind the tires prevent debris from hitting other vehicles. During your pre-trip inspection, check that splash guards are present, undamaged, securely mounted, and not dragging on the ground or rubbing on the tires.

Not quite. The answer is Fuel tank(s)

While inspecting the side of your vehicle, check that the fuel tanks are securely mounted and their fuel filler caps are tight. Also make sure that neither the tanks nor the fuel lines are leaking.