Indiana CDL: Combination Vehicles Practice Test

Not quite. The answer is Turn wide as you complete your turn.

To turn right, you may need to turn wide to help prevent the rear end of your vehicle from overrunning the curb. However, if you swing wide to the left before you turn right, another driver may try to pass you on your right, which can lead to a collision. Instead, start the right turn with the rear of your vehicle as close to the curb as possible and then turn wide as you complete the turn. This will deny drivers room on the right to try to pass you.

Not quite. The answer is release the brakes.

Once you realize your vehicle is in a skid, you should release the brakes so that the wheels can grip the road again. The trailer will start to follow the tractor and straighten out.

Not quite. The answer is "Bobtail" tractors can take longer to stop than a combination vehicle loaded to the maximum gross weight.

When a combination vehicle is empty or lightly loaded, its braking distance increases. The very stiff suspension springs and strong brakes give poor traction and make it very easy to lock the wheels. Likewise, "bobtail" tractors (tractors without semitrailers) can take longer to stop than a fully loaded tractor-trailer. Be very careful when driving a "bobtail" tractor.

Not quite. The answer is If the trailer has no spring brakes, you will be able to drive away but you won't have trailer brakes.

Trailers built before 1975 are not required to have spring brakes. If you cross the air lines when coupling such a trailer, you may have no air pressure to supply the trailer brakes. You'll be able to drive, but you won't be able to brake the trailer. Always test the trailer air brakes before you start to drive.

Not quite. The answer is 20 to 45 psi.

The tractor protection valve is located in the tractor, usually at the rear of the cab. Its purpose is to keep air in the tractor's air brake system should the trailer break away or develop a bad leak. The tractor protection valve is designed to close automatically if the air pressure falls into the range specified by the manufacturer, typically 20–45 psi.

Not quite. The answer is A triple 27-foot trailer

Because of rearward amplification (causing the crack-the-whip effect), the last trailer in a combination vehicle has the highest probability of rolling over. The last trailer in a triple combination is more likely to roll over than the last trailer in a double combination.

Not quite. The answer is Adjust the air supply knob to send air to the trailer brakes. Turn off the engine once the air pressure normalizes. Then listen for the sound of escaping air as the brakes are released.

After coupling, make sure that the air lines are not crossed. To do this, send air to the trailer brakes by adjusting the "air supply" knob to normal. Let the pressure normalize. Then turn off the engine and test the brakes. You should see and hear the brakes in action and then see the air pressure normalize again.

Not quite. The answer is the trailer emergency glad hand.

During the coupling process, after you've backed the tractor till it's touching the trailer and you've parked the tractor, it's time to connect the air lines. Connect the tractor emergency air line to the trailer emergency glad hand. Connect the tractor service air line to the trailer service glad hand.

Not quite. The answer is check the air line connections.

If you cross the emergency and service air lines, air will flow to the service line instead of the trailer air tanks. Air won't be available to release the spring brakes. Therefore, if the spring brakes don't release when you push the trailer air supply control, check the air line connections.

Not quite. The answer is Yes, if you're not sure of your path of travel.

Backing a combination vehicle is potentially hazardous. Before you start to back up, check your intended path of travel. Exit the cab and walk around the vehicle. Check your clearance to the sides and overhead, in and near the path of your vehicle.

Not quite. The answer is open

When uncoupling, unlock the fifth wheel by raising the release handle lock and pulling the release handle to the open position. When you do this, keep your legs and feet well clear of the tractor's rear wheels in case the vehicle moves.

Not quite. The answer is Upper and lower fifth wheel, air lines, and electrical lines

When making a visual check of the coupling, be sure to check the upper and lower fifth wheel, air lines, and electrical lines.

Not quite. The answer is A 3-axle tractor towing two 27-foot trailers

When any vehicle turns, its rear wheels will follow a shorter path than its front wheels. This is called off-tracking or "cheating." The longer the vehicle, the greater the difference. In a combination vehicle, the trailer's wheels will off-track more than the tractor's rear wheels. In a double or triple combination vehicle, the wheels of the last trailer will off-track the most.

Not quite. The answer is secured but with enough slack for turns.

During your walk-around inspection, make sure that the electrical and air lines are secure but have enough slack to stay attached and secure even when the vehicle is turning.

Not quite. The answer is step on and off the brake pedal several times.

To test the tractor protection valve, charge the trailer air brake system, turn off the engine, and lower the air pressure by stepping on and off the brake pedal several times. The tractor protection valve control (also called the trailer air supply control) should pop out (or go from the “normal” to the “emergency” position) when the air pressure falls into the range specified by the manufacturer (typically 20–45 psi).

Not quite. The answer is supply air to the trailer system and then pull out the air supply knob.

Before backing under the trailer, check that the trailer brakes are working and then lock the trailer brakes. Once you've attached the air lines, there are a number of checks you should make: Check the glad hand seals. Make sure that the air lines won't be caught or crushed when you back under the trailer. Charge the trailer air brake system and verify that it's working without significant air loss. Then set the trailer air supply control to shut off the air and put on the trailer emergency brakes.

Not quite. The answer is applying and releasing the trailer brakes and listening for brake sounds.

After you've connected the air lines, double-check the connection and make sure the brakes are working. Shut off the engine so you can hear the brakes. Apply the brakes and listen for the sound of the brakes being applied. Release the brakes and listen for the hiss of escaping air.

Not quite. The answer is Neutral

Before you inspect the trailer supports of the landing gear, secure the tractor by applying the parking brake and placing the transmission in Neutral.

Not quite. The answer is the coupling is not right and should be fixed before you drive the coupled unit.

Don't drive the vehicle until you're sure that the coupling is correct. Check to make sure of the following: There is no space between the upper and lower fifth wheel, the fifth wheel jaws have closed around the shank of the kingpin, the locking lever is in the "lock" position, and the safety latch is in position over the locking lever. If anything isn't right, don't drive the vehicle until you've found and corrected the problem. If you drive it anyway, your trailer could come loose while you're driving.

Not quite. The answer is your brakes might fail.

On a combination vehicle, the brakes on the tractor and all trailers must work properly. If your combination vehicle is equipped with air brakes, check that air flows to all trailers and test both the trailer service brakes and the trailer emergency brakes.