South Carolina CDL: Double & Triple Trailers Practice Test

Not quite. The answer is enough to remove some of the trailer's weight from the converter dolly.

Lower the landing gear of the second semitrailer enough to remove some of the trailer's weight from the converter dolly. This will make it easier to pull the dolly out from under the trailer.

Not quite. The answer is both of the above are true.

Check each landing gear to be sure that it is fully raised. Also check that no parts are missing and it isn't bent or damaged.

Not quite. The answer is the tractor protection valve control (trailer air supply control) will pop out or go from "normal" to "emergency."

When you test the tractor protection valve, the tractor protection valve control (also called the trailer air supply control) should pop out or go from the "normal" to the "emergency" position. This shows that the tractor protection valve has closed automatically to keep the air pressure from falling too far.

Not quite. The answer is less

Double and triple vehicles are more prone to rolling over or jackknifing than single vehicles are. Avoid sudden braking or steering changes. Look far enough ahead that you can slow down or change lanes gradually when necessary.

Not quite. The answer is open the shut-off valves at the rear of the first trailer and close the shut-off valves at the rear of the second trailer.

Air must travel through the air lines of the tractor and all trailers – and that's all. Open the shut-off valves at the rear of each trailer but the last one to enable the air to travel to the trailer behind it. Close the shut-off valves at the rear of the last trailer to keep air from escaping.

Not quite. The answer is only the more common types of combinations.

The official CDL manual's section on double and triple trailers usually describes how to couple and uncouple the more common types of double and triple combinations. However, there are other ways of coupling and uncoupling the many types of truck-trailer and tractor-trailer combinations that are in use. To learn how to couple and uncouple the vehicles you will be driving, consult the manufacturer's or owner's specifications.

Not quite. The answer is apply light pressure on the brakes.

Avoid driving through deep puddles or flowing water if possible. If not, slow down and downshift into a low gear. Gently press on the brakes and maintain pressure for a short distance when you are out of the water. This will heat up the brakes and dry them out. (However, don't overdo it, or the brakes may overheat.) Then apply the brakes to make a test stop when it is safe to do so.

Not quite. The answer is rear.

Vehicles with double or triple trailers can experience a dangerous "crack-the-whip" effect, caused by rearward amplification. If you make a quick lane change, the crack-the-whip effect can turn the trailers over. (There have been many accidents where only the trailer overturned.) Rearward amplification is strongest at the rearmost trailer. Therefore, position your heaviest trailer at the front and your lightest trailer at the rear.

Not quite. The answer is directly in front of the converter dolly.

Back the first trailer into position in front of the tongue of the dolly. Hook the dolly to the pintle hook on the first trailer. Then latch the pintle hook securely. Raise the dolly's landing gear.

Not quite. The answer is open; closed

When you are inspecting a double or triple combination, make sure that the service and emergency line shut-off valves are open at the rear of each trailer except the last trailer, where they must be closed.

Not quite. The answer is Brake and downshift in the curve.

Before entering a curve, slow down to a safe speed and downshift into the right gear. This lets you use some power through the curve to help keep the vehicle stable through the curve. It also allows you to speed up as soon as you are out of the curve.

Not quite. The answer is closed.

A pre-trip inspection of a double or triple combination vehicle includes an inspection of each converter dolly in the vehicle. Among other things, check that the converter dolly air tank drain valve is closed.

Not quite. The answer is B.

If you swing wide to the left before you turn right, another vehicle may try to pass you on your right while you are turning. Instead, as shown in path B, make the right turn with the rear of your vehicle as close to the curb as possible and turn wide as you complete the turn. This will deny other vehicles enough room on the right to try to pass you.

Not quite. The answer is An additional drawbar

The type of converter dolly described in your official state CDL manual is an A-dolly. It has a single drawbar, whose eye fits over the pintle hook in the rear of a semitrailer. The A-dolly can pivot or articulate on that pintle hook. In contrast, a B-dolly (or C-dolly) has two drawbars, each with its own eye. These fit over two pintle hooks in the rear of a trailer. These two connections prevent the B-dolly from pivoting on the pintle hooks, thus eliminating one articulation or pivot point. B-dollies are used to connect B-doubles (also called B-train doubles).

Not quite. The answer is Open at the rear of the front trailers and closed at the rear of the last trailer

Air must travel through the air lines of the tractor and all trailers – and that's all. Open the shut-off valves at the rear of each trailer but the last one to enable the air to flow to the trailer behind it. Close the shut-off valves at the rear of the last trailer to keep air from escaping.

Not quite. The answer is restore traction to the tires.

If braking or steering force exceeds the tires' traction with the road surface, a skid may result. You can recover from the skid by restoring sufficient traction.

Not quite. The answer is drive through quickly.

If you drive through water at higher speeds, your tires may lose their grip of the road and start to skid. When driving through water, slow down and shift into a low gear. Increase engine rpm and apply the brakes gently to keep the brake linings pressed against the brake drums or discs. This will help keep contaminants out of the brakes.

Not quite. The answer is latched.

When coupling a converter dolly to the trailer in front of it, place the dolly's pintle eye on the trailer's pintle hook. Latch the pintle hook closed. Secure the dolly's safety chains to the trailer.

Not quite. The answer is the rear trailer of a triple.

In a double or triple combination, each trailer is more likely to roll over than the one in front of it. The rear trailer of a triple is 3.5 times as likely to roll over as a five-axle tractor-trailer. This is known as rearward amplification or the "crack-the-whip effect." For safety, position the heaviest trailer in front and the lightest trailer in the rear.

Not quite. The answer is The pintle eye of the dolly should be in place in the pintle hook of the trailer.

A pre-trip inspection of a double or triple combination vehicle includes an inspection of each converter dolly in the vehicle. Among other things, check the coupling of the dolly to the trailer in front. Make sure that the pintle eye of the dolly is in place in the pintle hook of the trailer, and the pintle hook is latched closed.