New Hampshire CDL: Double & Triple Trailers Practice Test

Not quite. The answer is An additional drawbar

The type of converter dolly described in your official state CDL manual is an A-dolly. It has a single drawbar, whose eye fits over the pintle hook in the rear of a semitrailer. The A-dolly can pivot or articulate on that pintle hook. In contrast, a B-dolly (or C-dolly) has two drawbars, each with its own eye. These fit over two pintle hooks in the rear of a trailer. These two connections prevent the B-dolly from pivoting on the pintle hooks, thus eliminating one articulation or pivot point. B-dollies are used to connect B-doubles (also called B-train doubles).

Not quite. The answer is enough to take some of the weight off the dolly.

When uncoupling a loaded second or third semitrailer, lower the landing gear until it makes firm contact with the ground. Then crank the landing gear in low gear for a few more turns – just enough to lift some weight off the dolly, but not so much that you lift the trailer off the fifth wheel. This will make it easier to unlatch the fifth wheel now and couple the trailer next time.

Not quite. The answer is Use wheel chocks.

If the second trailer doesn’t have spring brakes, drive the tractor close to the trailer, connect the emergency line, charge the trailer air tank, and disconnect the emergency line. This will set the trailer emergency brakes (assuming the slack adjusters are correctly adjusted). However, if you have any doubt about the effectiveness of the trailer's braking system, chock the wheels.

Not quite. The answer is 2

In this context, articulation or pivoting means movement between two units separated by a joint, such as between a tractor and a trailer. The standard or STAA doubles described in your official state CDL handbook are connected with an A-dolly, which has a single drawbar connected to the front trailer. However, a B-double (also called a B-train double) has a two-drawbar B-dolly (or C-dolly), which is connected to two hitches in the front trailer. The two drawbar connections prevent this type of dolly from pivoting on the front trailer. The rear trailer connects to the dolly's fifth wheel. Hence, the only two pivot points are the tractor's fifth wheel and the B-dolly's fifth wheel. B-trains are legal in parts of Michigan and Washington State.

Not quite. The answer is 11

The formula for following distance is one second per ten feet of vehicle length, plus an extra second if you are traveling over 40 mph. Therefore, for a 100-foot vehicle traveling at 50 mph, you should leave a following distance of 100/10 + 1 = 11 seconds.

Not quite. The answer is Doubles/triples flip over from quick steering movements more easily than do many other vehicles.

Because of rearward amplification (the "crack-the-whip" effect), steering changes affect the rearmost trailer much more than they affect the front trailer or the tractor. Avoid quick or sharp steering changes that could cause the rearmost trailer to roll over.

Not quite. The answer is a yellow lamp on the left side.

A converter dolly with antilock brakes is required to have a yellow ABS lamp on its left side. All converter dollies built since March 1, 1998 have antilock brakes.

Not quite. The answer is Check for normal air pressure. Release the parking brakes. Pull forward slowly. Apply the trailer brakes, using the hand control if so equipped.

Checking your trailer's service brakes is a four-step process: 1. Check for normal air pressure. 2. Release the parking brakes. 3. Pull your vehicle forward slowly. 4. Apply the trailer brakes, using the hand control (trolley valve) if so equipped. If the trailer brakes are properly connected and working, you should feel them come on at this point.

Not quite. The answer is slowly pull clear of the converter dolly.

The last step in the process of uncoupling twin trailers is to slowly pull clear of the converter dolly. The other two choices are previous steps in this process.

Not quite. The answer is A truck has less traction when it's empty than when it's fully loaded.

Trucks that are empty or only lightly loaded take longer to stop because the stiff suspension springs and strong brakes give poor traction and make it easier to lock the wheels.

Not quite. The answer is You should avoid traveling alongside other vehicles whenever possible.

Whenever another vehicle is traveling alongside yours, there's always a chance that the vehicle might try to move into your lane and accidentally hit your vehicle. Also, the vehicle is blocking you from changing lanes. It's safer to find an open spot where there are no vehicles on either side of you. (Of course, that may not be possible in heavy, congested traffic.)

Not quite. The answer is a separate air tank.

Federal regulations require brakes on every wheel of a combination vehicle, including the wheels of the semitrailers and converter dollies. Like semitrailers, dollies have their own air brakes and their own air tanks.

Source: 49 CFR § 393.42

Not quite. The answer is closed.

A pre-trip inspection of a double or triple combination vehicle includes an inspection of each converter dolly in the vehicle. Among other things, check that the converter dolly air tank drain valve is closed.

Not quite. The answer is that you can pull straight through.

When parking a long vehicle, you should look for a parking space that you can go straight through rather than back out of. Also note the layout of the parking lot and your parking space's location within it so you won't have difficulty exiting the parking space later.

Not quite. The answer is using the dolly's parking brake control.

To connect the converter dolly to the first semitrailer, release the dolly's brakes so it can be moved. You release the dolly's brakes by opening the air tank petcock (valve) or using the dolly's parking brake control if the dolly is equipped with spring brakes.

Not quite. The answer is Uncouple the third semitrailer from the second dolly.

To couple a triple-trailer combination, you couple the tractor and first semitrailer to the second and third semitrailers. But to uncouple the triple-trailer combination, you start by just uncoupling the third semitrailer from the rest of the combination.

Not quite. The answer is the tractor protection valve control (trailer air supply control) will pop out or go from "normal" to "emergency."

When you test the tractor protection valve, the tractor protection valve control (also called the trailer air supply control) should pop out or go from the "normal" to the "emergency" position. This shows that the tractor protection valve has closed automatically to keep the air pressure from falling too far.

Not quite. The answer is to lower its landing gear.

After you have uncoupled the rear trailer from the converter dolly, you need to uncouple the converter dolly from the front trailer. You do this as follows: 1. Lower the landing gear of the dolly. 2. Disconnect the safety chains. 3. Apply the dolly's spring brakes or chock its wheels to keep the dolly from moving. 4. Release the pintle hook connecting the dolly to the trailer ahead of it. 5. Slowly pull clear of the dolly.

Not quite. The answer is A sudden movement with the steering wheel can result in a tipped-over rear trailer.

Because of rearward amplification (the "crack-the-whip" effect), the rearmost trailer is much more prone to rolling over. Avoid sudden steering changes that could cause the rearmost trailer to roll over.

Not quite. The answer is The heaviest trailer

The rearmost trailer is much more likely to roll over than the front trailer. Position the heaviest trailer directly behind the tractor and position the lightest trailer at the rear.