Massachusetts CDL: Double & Triple Trailers Practice Test

Not quite. The answer is slowly pull clear of the converter dolly.

The last step in the process of uncoupling twin trailers is to slowly pull clear of the converter dolly. The other two choices are previous steps in this process.

Not quite. The answer is a separate air tank.

Federal regulations require brakes on every wheel of a combination vehicle, including the wheels of the semitrailers and converter dollies. Like semitrailers, dollies have their own air brakes and their own air tanks.

Source: 49 CFR § 393.42

Not quite. The answer is using the dolly's parking brake control.

To connect the converter dolly to the first semitrailer, release the dolly's brakes so it can be moved. You release the dolly's brakes by opening the air tank petcock (valve) or using the dolly's parking brake control if the dolly is equipped with spring brakes.

Not quite. The answer is Check for normal air pressure. Release the parking brakes. Pull forward slowly. Apply the trailer brakes, using the hand control if so equipped.

Checking your trailer's service brakes is a four-step process: 1. Check for normal air pressure. 2. Release the parking brakes. 3. Pull your vehicle forward slowly. 4. Apply the trailer brakes, using the hand control (trolley valve) if so equipped. If the trailer brakes are properly connected and working, you should feel them come on at this point.

Not quite. The answer is the tractor protection valve control (trailer air supply control) will pop out or go from "normal" to "emergency."

When you test the tractor protection valve, the tractor protection valve control (also called the trailer air supply control) should pop out or go from the "normal" to the "emergency" position. This shows that the tractor protection valve has closed automatically to keep the air pressure from falling too far.

Not quite. The answer is Check your mirrors to keep an eye on your tires.

Use the mirrors to keep an eye on your tires. It's one way to spot a tire fire. But your mirrors don't eliminate all blind spots. Your truck still has large blind spots, often called No-Zones.

Not quite. The answer is you couple the third trailer to the second trailer before you couple them to the first trailer.

A triple combination vehicle has four units (not counting the converter dollies): a tractor and three trailers. You couple a triple as follows: 1. Couple the first trailer to the tractor the same way that you couple any combination vehicle. 2. Couple the third trailer to the second trailer using the method for coupling doubles (which will involve the use of a converter dolly). 3. Move another converter dolly into position. 4. Couple the tractor and first trailer to the second and third trailer using the method for coupling doubles (which will involve another converter dolly).

Not quite. The answer is Turnpike double trailer

A double pup trailer consists of two 28.5-foot trailers, known as "pup trailers." A double pup trailer is also known as an STAA trailer, named for the Surface Transportation Assistance Act (STAA). This is the only type of double trailer that is allowed nationwide. A Rocky Mountain double trailer consists of a 40- to 53-foot trailer followed by a 28.5-foot pup trailer. Rocky Mountain doubles are allowed in certain Western states. A turnpike double trailer consists of two 48-foot trailers. Turnpike doubles can be found traveling on expressways in the Eastern states.

Not quite. The answer is slow down.

You should always be able to stop within the distance you can see ahead. Your low-beam headlights let you see only about 250 feet ahead. At 55 mph, your vehicle will travel 250 feet in just 3.1 seconds – not enough time to notice and safely avoid a hazard that's within 250 feet of you. At 30 mph, your vehicle will travel 250 feet in 5.7 seconds.

Not quite. The answer is March 1998.

Antilock brakes have been required on all tractors built since March 1, 1997. Antilock brakes have been required on all trailers, converter dollies, buses, and single trucks built since March 1, 1998.

Not quite. The answer is use controlled or stab braking.

Hard braking and turning at the same time is likely to cause a skid. You should brake in a way that will keep your vehicle in a straight line and allow you to turn if necessary. If you need to brake suddenly to avoid a crash, use controlled braking or stab braking (but don't use stab braking if your vehicle has antilock brakes).

Not quite. The answer is Rocky Mountain double

A double pup trailer consists of two 28.5-foot trailers, known as "pup trailers." A double pup trailer is also known as an STAA trailer, named for the Surface Transportation Assistance Act (STAA). This standard-double configuration is the only type of double trailer that is allowed nationwide. A Rocky Mountain double trailer consists of a 40- to 53-foot trailer followed by a 28.5-foot pup trailer. Rocky Mountain doubles are allowed in certain Western states. A turnpike double trailer consists of two 48-foot trailers. Turnpike doubles can be found traveling on expressways in the Eastern states.

Not quite. The answer is If there are vehicles on both sides of you, a move to the right may still be best.

To avoid a head-on collision, steer right toward the shoulder or curbline. Even if you are blocked on both sides by other vehicles, a move to the right may still be best. At least you won't force other drivers into an opposing traffic lane, possibly involving them in a head-on collision. Prepare to drive entirely off the roadway to the right if necessary to avoid a head-on collision. Head-on collisions are often fatal.

Not quite. The answer is 10

The formula for following distance is one second per ten feet of vehicle length, plus an extra second if you are traveling over 40 mph. Therefore, for a 100-foot vehicle traveling at 30 mph, you should leave a following distance of 100/10 = 10 seconds. (At or below 40 mph, you do not add an extra second.)

Not quite. The answer is closed; latched

When you do a walk-around inspection, you must ensure that the converter dolly is properly connected to the front trailer. Check that the pintle hook of the front trailer is locked onto the eye hook of the converter dolly and properly latched. Otherwise, the dolly could come loose. Even worse, if the dolly comes loose while it's still coupled to the rear trailer, the tow bar could fly up, possibly injuring someone.

Not quite. The answer is 3

In this context, articulation or pivoting means movement between two units separated by a joint, such as between a tractor and a trailer. The standard or STAA double combination in the CDL handbook has 3 points of articulation: (1) the fifth wheel of the tractor; (2) the pintle hook of the front trailer; (3) the fifth wheel of the converter dolly.

Not quite. The answer is You must drive a double or triple very smoothly to avoid a rollover or jackknife.

Take special care when pulling two or three trailers. Doubles and triples are more likely to turn over than other combination vehicles because of the "crack-the-whip" effect. You must steer gently when pulling trailers. To prevent the trailers from rolling over, you must steer gently and go slowly around corners, on-ramps, off-ramps, and curves.

Not quite. The answer is Neither of the above will cause it.

Despite what footnote 5 in 49 CFR 393.11 says, Operational Policy 15 of the North American Standard Out-of-Service Criteria states that a converter dolly must have one stop lamp, one tail lamp, and (if the dolly obscures the tractor's rear turn signals) turn signal lights, but only when the dolly is being towed singly and is not towing a trailer. In a full multi-trailer configuration, the rearmost trailer must have working stop lights and taillights, of course.

Not quite. The answer is B.

If you swing wide to the left before you turn right, another vehicle may try to pass you on your right while you are turning. Instead, as shown in path B, make the right turn with the rear of your vehicle as close to the curb as possible and turn wide as you complete the turn. This will deny other vehicles enough room on the right to try to pass you.

Not quite. The answer is drive through quickly.

If you drive through water at higher speeds, your tires may lose their grip of the road and start to skid. When driving through water, slow down and shift into a low gear. Increase engine rpm and apply the brakes gently to keep the brake linings pressed against the brake drums or discs. This will help keep contaminants out of the brakes.