Iowa CDL: Tanker Vehicles Practice Test

Not quite. The answer is Get out of your vehicle and away from the tracks.

If your vehicle gets stuck on a railroad track, get everyone including yourself out of your vehicle. Have everyone walk at about a 45-degree angle to the tracks in the direction from which you expect a train to approach. That way, if your vehicle is hit, none of you will be struck by flying debris. Once you've reached a safe location, call 911 or the telephone number on the railroad crossing sign.

Not quite. The answer is Slow to a safe speed before entering, then accelerate slightly through the curve.

The posted speed for a curve may be safe for cars but not for tankers because of their relatively high center of gravity. Tests have shown that a tanker can roll over on a curve when traveling at the posted speed. The safest way to take a curve in a tanker is to slow down before the curve and then accelerate slightly through the curve. Braking in a curve risks a skid.

Not quite. The answer is your vehicle will stay in a straight line.

If you must brake in an emergency, brake in a way that keeps your vehicle in a straight line while still letting you turn if necessary. You can use the "controlled braking" method or (in a vehicle without antilock brakes) the "stab braking" method.

Not quite. The answer is 20 feet long.

An ISO standard portable tank is a metal tank enclosed in a steel frame. The frame is 19.8556 feet (6.05 meters) long, 7.874 feet (2.40 meters) wide, and either 7.874 feet (2.40 meters) high or 8.374 feet (2.55 meters) high.

Not quite. The answer is Inspect the vehicle.

Before loading, unloading, or driving a tanker, you must inspect the vehicle. This makes sure that the vehicle is safe to carry liquids or gases and is safe to drive. Tank vehicles have special items that you need to check. Study the vehicle's operator manual to learn how to inspect your tank vehicle.

Not quite. The answer is you have to press the brake pedal harder than usual to control your speed.

If your brakes begin to fade, you'll notice that you have to depress the brake pedal harder to achieve the same braking effect as before. If your vehicle is so equipped, check the application pressure gauge to see just how much pedal effort you are employing. If the brakes continue to fade, you may not be able to slow down or stop at all.

Not quite. The answer is baffles.

Baffles are devices that regulate the flow of liquid. In a tank vehicle, baffles are a type of bulkhead with holes through which liquid may flow but with reduced force.

Not quite. The answer is a high center of gravity.

It takes special skills to drive a tanker carrying liquid cargo because of the vehicle's high center of gravity and the possibility that the liquid cargo may surge forward and backward or from side to side. Much of a loaded tanker's weight is carried five or six feet above the ground. This makes a tanker top-heavy, which makes it more prone to rollovers than other types of vehicles. Tests have shown that a tank vehicle can roll over at the speed limits posted for curves. The safest way to take a curve in a tanker is to slow down well below the posted speed limit before you enter the curve.

Not quite. The answer is 70%

It takes special skills to operate a tank vehicle safely. About 70% of tank truck drivers haul hazardous materials, such as gasoline. Doing so takes even more special skills. Such drivers must obtain both a tank vehicle (N) endorsement and a hazardous materials (H) endorsement on their CDLs, or a combination tank vehicle and hazardous materials (X) endorsement.

Not quite. The answer is both of the above.

When deciding how much liquid you can load on your tank vehicle, you must consider the weight of the liquid, the amount of space to allocate for the liquid to expand as it heats up (called outage), and all legal weight limits on your vehicle. A full tank of a dense liquid may exceed the legal weight limits, so you can only fill the tanks partially with such a liquid.

Not quite. The answer is Rear

Shut-off valves are used in the service and supply air lines at the rear of trailers used to tow other trailers. These valves permit closing off the air lines when another trailer is not being towed. You must check that all shut-off valves are in the open position except the ones at the rear of the last trailer, which must be closed.

Not quite. The answer is closed before you drive the vehicle.

To help prevent leaks, close all manhole covers before you drive the vehicle.

Not quite. The answer is You should not load a cargo tank completely full.

Some liquids expand significantly when they warm up. To fill a tank with such a liquid, you must leave some room in the tank (called "outage") to take the expansion. Different liquids expand at different rates as the temperature increases. In science, the percentage increase of expansion for a given change in temperature is called the coefficient of thermal expansion. This value depends on the type of liquid. You need to find out how much outage you will need to allow for the type of liquid you'll be hauling.

Not quite. The answer is partly engage the clutch before you take your right foot off the brake.

When you start your vehicle, avoid rolling backward or else you may hit someone behind you. Set the parking brake whenever necessary to keep from rolling back. Release the parking brake only when you have applied enough engine power to keep from rolling back. If you have a manual transmission vehicle, partly engage the clutch before you take your right foot off the brake. On a tractor-trailer equipped with a trailer brake hand valve, the hand valve can be applied to keep from rolling back.

Not quite. The answer is Much of the tanker's weight is high up off the ground.

An object with a high center of gravity is top-heavy; much of its weight is high off the ground. Top-heavy objects are more prone to toppling over. Loaded tankers tend to have a high center of gravity because the tanks are so tall. This makes liquid tankers more prone to rolling over. Tests have shown that tankers can roll over on curves even at the speeds posted. On curves, slow down well below the posted speeds.

Not quite. The answer is Upshift.

If your hydraulic brakes fail while you're driving, try pumping the brake pedal to build up enough hydraulic pressure to stop your vehicle. If this fails, downshift to use engine braking and apply the parking brake. Release the parking brake before you lock the wheels. If all else fails, look for an escape route. Head for an escape ramp or an open field and let your vehicle slow to a stop.

Not quite. The answer is 250 feet.

You should always be able to stop within the distance you can see ahead. Fog, rain, or other conditions may require that you slow down to be able to stop in the distance you can see. If your headlights let you see only 250 feet ahead, adjust your speed so that you can stop within that distance. Otherwise, by the time you notice a hazard ahead, you may not be able to stop in time to avoid it.

Not quite. The answer is You will continue in a straight line and keep moving forward no matter how you steer.

In a front-wheel skid, the front end of your vehicle tends to travel in a straight line regardless of how you turn the steering wheel. This type of skid is most often caused by driving too fast for the current driving conditions. Therefore, the best way to recover from this type of skid is to just let the vehicle slow down. Steer and brake only gently.

Not quite. The answer is Both of the above are true.

Tank vehicles have a high center of gravity, typically five or six feet above the ground. This makes a tanker top-heavy, which makes it more prone to rollovers than other types of vehicles. Tests have shown that a tank vehicle can roll over at the speed limits posted for curves. To take an upcoming curve safely, slow down well below the posted speed limit.

Not quite. The answer is some liquids expand more than others when they get warm.

Different liquids expand at different rates as the temperature increases. In science, the percentage increase of expansion for a given change in temperature is called the coefficient of thermal expansion. This value depends on the type of liquid. You need to find out how much outage you will need to allow for the type of liquid you'll be hauling.