Colorado CDL: Pre-Trip Inspection Practice Test

Not quite. The answer is Drive shaft

The drive shaft transmits torque from the transmission and the gear box to the drive wheels. During your pre-trip inspection, check that the drive shaft is not bent or cracked and the U-joints aren't loose or worn. While you're driving, a dropped drive shaft could be very serious.

Not quite. The answer is Ammeter or voltmeter

During your pre-trip inspection, check the ammeter gauge or voltmeter gauge to make sure that the alternator or generator is charging properly or the warning light is off.

Not quite. The answer is Fire extinguisher and warning devices for stopped vehicles

Federal regulations require every CMV to carry one of the following sets of warning devices in case the driver must stop the CMV on the road: three reflective triangles and a fire extinguisher. Spare electrical fuses are no longer federally required emergency equipment under current FMCSA regulations. States may require extra emergency equipment on certain vehicles.

Source: 49 CFR 393.95

Not quite. The answer is Spacers

Wheel spacers adjust wheel offset. During your pre-trip inspection, inspect each wheel that has wheel spacers to make sure that no spacers are missing, bent, damaged, or rusted through. Make sure that dual tires aren't touching. Dual tires that touch can catch fire.

Not quite. The answer is Release arm

The release arm allows you to disengage the fifth-wheel locking jaws so you can uncouple the trailer. During your pre-trip inspection, check that the release arm is in the engaged position and the safety latch (if so equipped) is in place.

Not quite. The answer is The windshield and mirrors

Windshields and mirrors should be clean and free of damage, illegal stickers, or obstructions that could impede visibility.

Not quite. The answer is When you start the engine, the oil temperature gauge should climb to the normal operating range.

When you start the engine, the oil temperature gauge should begin a gradual rise to the normal operating range. (The oil may take longer than the coolant to warm up.) If the gauge doesn't rise, the oil temperature sensor may have failed.

Not quite. The answer is Leaks

As part of your engine inspection, check the ground below the engine compartment for puddles or dripping liquids.

Not quite. The answer is Doors

During your pre-trip inspection, check that the doors to your vehicle are undamaged and that they open and close properly from the outside. The hinges should be secure with seals intact. Note: If you're inspecting a passenger vehicle, there are additional checks you should perform on the passenger entry doors and the emergency exit doors.

Not quite. The answer is Dash indicators

During your pre-trip inspection, test that the dash indicators work when the following corresponding lights are turned on: the left turn signal, the right turn signal, the four-way emergency flashers, and the high-beam headlights.

Not quite. The answer is Lug nuts

During your pre-trip inspection, check that all lug nuts are present and accounted for, tightly fastened, and free of cracks or distortions.

Not quite. The answer is Over the trailer bumper; hooks face downward

During your pre-trip inspection, make sure that the safety chains are crossed (if they are long enough for that). Make sure that the safety chains are hooked over the trailer bumper and onto the trailer so that the hooks face downward.

Not quite. The answer is Landing gear

You check the landing gear when you inspect the side of the trailer.

Not quite. The answer is Tandem release arm / locking pins

If so equipped, make sure that the locking pins are locked in place and the release arm is secured.

Not quite. The answer is battery

During your pre-trip inspection, check the battery to make sure that its connections are tight and not excessively corroded. Also check that the door or cover of the battery box is secure and undamaged.

Not quite. The answer is the parking brakes

Test the parking brakes first. Then to test the service brakes, start by releasing the parking brakes.

Not quite. The answer is Clutch and gearshift

To ensure that your vehicle doesn't move once you start the engine, first depress the clutch (unless the vehicle has an automatic transmission) and put the gearshift in neutral (or Park for an automatic transmission). Once the engine has started, slowly release the clutch.

Not quite. The answer is If it's a cab-over vehicle

In a conventional vehicle, the engine is mounted forward of the driver. In a cab-over vehicle (also known as a cab-forward vehicle), the cab is located above, or even in front of, the front axle. To inspect a cab-over vehicle, it may be necessary for you to tilt the cab to gain access to the engine compartment. Before doing this, secure any loose items inside the cab so they won't fall when you tilt the cab.

Not quite. The answer is Hearing

When you inspect the air lines, listen for the telltale hiss of escaping air, which indicates an air leak.

Not quite. The answer is Rim

The rim is the outer part of the wheel, to which a tire is attached. A damaged rim can result in loss of the tire from the rim, loss of the wheel from the axle, loss of air pressure in the tire, or the wheel rolling off the rim because of damage to the flange. During your pre-trip inspection, check that the rim is undamaged and the flange isn't bent. Check that no welding repairs have been made to the rim. Finally, check that there are no rust trails (which might indicate that the rim is loose on the wheel).